- 1 What type of sprinkler system is not required to have a fire department connection?
- 2 What is a fire department connection Clapper?
- 3 Why is a Siamese connection used?
- 4 What does FDC on a building mean?
- 5 How high can a fire department connection be off the ground?
- 6 Which device activates the building fire alarm when water is flowing in a sprinkler system?
- 7 What psi do you pump a sprinkler system?
- 8 What pressure should I pump my sprinklers at?
- 9 What pressure do you pump a standpipe at?
- 10 How does a Siamese valve work?
- 11 How do Siamese connections work?
- 12 What is a Storz connection?
- 13 How does a fire riser work?
- 14 How does a standpipe work?
- 15 What is a FDC check valve?
What type of sprinkler system is not required to have a fire department connection?
A fire department connection ( FDC ) is required for most NFPA 13 and 13R automatic sprinkler systems and standpipe systems. They are not required for automatic sprinkler systems protecting one- and two-family dwellings and townhomes.
What is a fire department connection Clapper?
Clappers guide water through fire department connections Pressurized water moving through fire department connections can close built-in clappers. These clappers prevent water from exiting through open inlets. On an FDC with two or more inlets, clappers allow firefighters to add or remove hoses as needed.
Why is a Siamese connection used?
Siamese connections are to be equipped with plugs or caps. This is to prevent dirt and other foreign objects from entering the piping, which would inhibit water flow or prevent the connection from being used during an emergency.
What does FDC on a building mean?
FDC stands for Fire Department Connection. This is a connection on the exterior of a commercial building where a responding fire department can attach a fire hose and pump water into the building’s stand pipe system supplementing the water pressure to the buidling’s sprinkler system.
How high can a fire department connection be off the ground?
Fire department connections ( FDC ) shall be located not less than 18 inches and no more than 48 inches above the level of the adjoining ground (NFPA 14 Section 6.4.
Which device activates the building fire alarm when water is flowing in a sprinkler system?
Vane or paddle type waterflow detectors and pressure type switches are used to detect the flow of water in a fire sprinkler system and to send an alarm signal. Valve supervisory switches are used to monitor the open or closed position of the valves that control the water supply in the fire sprinkler system.
What psi do you pump a sprinkler system?
Water pressure is measured in pounds per square inch – also called psi. The average water pressure for most homes and businesses is between 30 psi and 50 psi; most sprinkler systems are designed to use pressures of around 30 psi.
What pressure should I pump my sprinklers at?
Setting the fire department pumper engine pressure 50 psi below the building system pressure will allow the building pump to stay running and do the job as long as it can. A pressure drop in the system of more than 50 psi is a good indication of a substantial amount of water flowing.
What pressure do you pump a standpipe at?
The minimum pressure while flowing the required standpipe flow (500 GPM from the hydraulically most remote standpipe and 250 GPM from each additional standpipe, up to a maximum of 1000 GPM for a fully sprinklered building) shall be 100 psi at any valve outlet while flowing 250 GPM through each valve.
How does a Siamese valve work?
Siamese FDCs will contain either a single or double clapper to channel the flow of water coming into the system. If two hoses are connected, the equal pressure will cause the clapper in the middle of the body to let water flow in from each side. Double clappers provide greater control.
How do Siamese connections work?
Inspired by the Y-shaped Siamese twins, a Siamese connection is a Y shaped fire department connection with two female inlets through which firefighters can attach two hoses and refill standpipes or sprinkler systems with water. The siamese connection is alternatively called FDC ( Fire Department Connection ).
What is a Storz connection?
Invented by Carl August Guido Storz in 1882, a Storz connection is a type of hose coupling used to connect large diameter hose to a fire sprinkler or standpipe system. Storz solves a common problem faced by firefighters: mismatches between couplings.
How does a fire riser work?
As a fire sprinkler discharges, water flows out of the pipe, or branch line, it’s connected to. When that happens, water moves through the system riser to refill the branch line. These changes in flow and pressure are monitored at the riser by electronic devices called water flow switches.
How does a standpipe work?
A standpipe is an open-ended, metal pipe that can be screwed into a basement floor drain to permit the flow of water back up as high as necessary, thereby delaying or preventing a basement flood.
What is a FDC check valve?
The most common component associated with a check valve is the FDC (Fire Department Connection). The fire department uses this as a means to help provide water to the sprinkler system in case of a fire.